Home | Dealer Locator | Contact Us
Band Clamp          Model BC-EC



 
3" Wide
Size Shipping Wt. Each Part Number
3/4" 0.50# 089998
1" 0.55# 089997
1-1/4" 0.65# 089996
1-1/2" 0.65# 089995
2" 1.00# 089994
3" 1.10# 089991
4" 1.25# 089989
6" 1.25# 089985
8" 1.65# 089984
6" Wide
Shipping Wt. Each Part Number
1.10# 089982
1.15# 089981
1.20# 089980
1.25# 089979
2.15# 089978
2.30# 089975
2.45# 089972
2.85# 089967
3.25# 089966

Economy Band Clamp

  • Economical Clamp for small pin-hole leaks.
  • Band is 304 Stainless Steel
  • Gasket material is Buna-N Rubber
  • Nodular Iron Lugs and alloy bolts with Heavy Hex nuts
  • Sizes 1/2" through 8" in 3" and 6" widths
  • Pressure Rating: 100psi.

Economical Model BC-EC Band Clamp design allows for quick one-man installation. Bolts fit into iron lugs without removing nuts. Installation Procedure:

• Thoroughly clean the damaged area with wire bursh. This will assure a bubble tight gasket seal.
• Back off the nuts to the end of the bolt, but do not remove them. Separate the clamp.
• Center the clamp gasket over the area that needs repair. Make sure the gasket extends past damaged area.
• Relocate the bolt heads securely into their receiving lugs. Tighten 3/8" bolts to 25 ft/lbs, 7/16" bolts 35ft/lbs on 2" & larger size.
• Pressure test for leaks before leaving area.


Band Clamp          Model BC-FC
 




3" Wide
Size Shipping Wt. Each Part Number
3/4" 0.70# 089930
1" 0.75# 089931
1-1/4" 0.83# 089932
1-1/2" 0.90# 089933
2" 1.50# 089934
6" Wide
Shipping Wt. Each Part Number
1.40# 089936
1.50# 089937
1.65# 089938
1.85# 089939
3.00# 089940

Economy Band Clamp

  • Features 360 degree gasket for sure seals.
  • Band is 304 Stainless Steel
  • Gasket material is Buna-N Rubber
  • Nodular Iron Lugs and alloy bolts w/ Hex nuts.
  • Sizes 3/4" through 2" in 3" and 6" widths
  • Pressure Rating: 100psi.

Economical Model BC-FC Full Circle Band Clamp design is similar to the above Model BC-EC Band Clamp but features a full circle gasket for added reliability. Installation Procedure:

• Thoroughly clean the damaged area with wire bursh. This will assure a bubble tight gasket seal.
• Back off the nuts to the end of the bolt, but do not remove them. Separate the clamp.
• Make sure the gasket extends past damaged area.
• Relocate the bolt heads securely into their receiving lugs. Tighten 3/8" bolts to 25 ft/lbs, 7/16" bolts 35ft/lbs on 2" size.
• Pressure test for leaks before leaving area.


Band Clamp          Model BC-SB


 
7 1/2" Width
Size Shipping Wt. Each Part Number
2" 4# 089941
3" 5# 089942
4" 6# 089943
6" 7# 089944
8" 8# 089945
10" 11# 089946
12" 13# 089947
12 1/2" Width
Shipping Wt. Each Part Number
5# 089948
6# 089949
8# 089950
10# 089951
11# 089952
16# 089953
18# 089954

All Stainless Steel Single Band

  • 18-8 Type 304 Stainless Steel band
  • 18-8 Type 304 Stainless Steel Bolts & Nuts
  • Gasket material is Buna-N Ruber
  • Side Bars and Lifter Bar 18-8 Stainless Steel
  • Sizes 2" through 12" in 7.5" or 12.5" widths
  • Pressure Rating: 150 psi

Model BC-SB all Stainless Steel Single Section Band Clamp design allows for quick one-man installation. Excellent design for applications on corrosive materials or on buried water mains where corrosive soil is present. Bolts fit into lugs without removing nuts. Installation Procedure:

• Thoroughly clean the damaged area with wire bursh. This will assure a bubble tight gasket seal.
• Back off the nuts to the end of the bolt, but do not remove them. Separate the clamp.
• Center the clamp gasket over the area that needs repair. Make sure the gasket extends past damaged area.
• Relocate the bolt heads securely into their receiving lugs.
• Pressure test for leaks before leaving area.
• Bolt Torque: 1/2" bolts 50-60 ft/lbs, 3/4" bolts 90-100 ft/lbs.


Band Clamp          Model BC-DB
 


7 1/2" Width
Size Shipping Wt. Each Part Number
4" 11# 089956
6" 12# 089957
8" 13# 089958
10" Width
10" 18# 089959
12" 19# 089960
12 1/2" Width
Shipping Wt. Each Part Number
18# 089961
19# 089962
21# 089963
12 1/2" Width
23# 089964
25# 089965

All Stainless Steel Double Band

  • 18-8 Type 304 Stainless Steel band
  • 18-8 Type 304 Stainless Steel Bolts & Nuts
  • Gasket material is Buna-N Rubber
  • Side Bars and Lifter Bar 18-8 Stainless Steel
  • Sizes 4" through 8" in 7.5" or 12.5" widths
  • Sizes 10" through 12" in 10" or 12.5" widths
  • Pressure Rating: 300 psi

Model BC-DB all Stainless Steel Double Band Clamp design allows for quick one-man installation. Excellent design for applications on corrosive materials or on buried water mains where corrosive soil is present. Bolts fit into lugs without removing nuts. Installation Procedure:

• Thoroughly clean the damaged area with wire bursh. This will assure a bubble tight gasket seal.
• Back off the nuts to the end of the bolt, but do not remove them. Separate the clamp.
• Center the clamp gasket over the area that needs repair. Make sure the gasket extends past damaged area.
• Relocate the bolt heads securely into their receiving lugs.
• Pressure test for leaks before leaving area.
• Bolt Torque: 1/2" bolts 50-60 ft/lbs, 3/4" bolts 90-100 ft/lbs.